![]() |
![]() |
![]() |
![]() |
![]() |
| HOMEPOST ADBROWSESEARCHADS BY DAYMOST RECENTMOST POPULARHONOR PAYMENTFORUMHELP! |
| Racing Classifieds | Store | RJ News | News | RJ Rides | Photos & Videos | MotorcycleAds | BoatingJunk | Directory | Contests |
| AD CATEGORY :: Drag Racing Cars :: Complete Race Cars |
Ad #1706439 Posted:2009-11-07 14:28:04
This ad expires in 64 days.
SPITZER RACE CARS
34 CHEVY ROADSTER
$42,000.00
Very low-run chassis. This is the competition eliminator version, with cantelever mounted Afco shocks with 4 link bars & the addition of a X link locator.
* 4130 C.M. chassis with all updates & new hammer tone powder coating
* Spitzer 9" fabricated rear with full chrome package, M.W. center section, axels & brakes
* Strange struts & brakes up front
* Carbon fiber seat enclosure, wheel tubs & dash insert
* Fuel system - Magna fuel 500 pump with Spitzer tank
* New Hoosier tires, front & rear with Aluma Star wheels
* Outlaw shifter with Biondo air shift
* Optima Red Top battery with 2nd battery provision
* Auto metered gauges
* MSD 7AL-2 ignition box with pro power coil & three step box
* Entirely professionally wired
etc., etc., etc.
ENGINE
* 505 CU. IN. BBC
* Cola crankshaft
* Eagle ESP rods with additional work & L-19 fasteners
* Ross pistons
* Comp Cams 7/4 swap cam
* Comps Best roller lifters
* Milidon ultra pan
* ATI balancer
* GM 4 bolt MK-4 block (289 casting)
* Arp studs on mains & heads
* Dart Pro-1 345 heads, programmed & flowed with sheet, now 354 C.C. intake runners, with Dart stainless valves, 2.300 & 1.880, Manley NexTech springs & titanium retainers, Jesel 1.7 shaft rockers with Trend Products pushrods
* Super Victor intake also programmed & flowed
* Pro Systems dominator flows 1098 CFM
* MSD distributor, crank trigger & plug wires, etc.
* Arp 12 point polished fasteners used throughout the assembly of this engine
TRANSMISSION & CONVERTER
* Janis/Rossler ProGlide with Dedenbear case & 1.80 straight cut planetary - all new
* ATI torque converter 8" with steel sprag built for this combo by "Nelson"
* ATI HD flywheel
* Showgun converter cooler (fan)
All parts on engine & trans combo are new with the exclusion of the engine block, which was pressure tested & professionally prepared.
PLEASE keep in mind this is a well thought out combination with zero runs. I am not looking to liquidate this car so be realistic.
Prelimarily, I would prefer emails on RJ's message system as opposed to phone calls. SERIOUS INQUIRIES ONLY.
Will separate this combination although the engine MUST sell first.
Complete car, 42,000
Roller, 28,500
Engine, 11,500
Trans & conv, 4,200
* 4130 C.M. chassis with all updates & new hammer tone powder coating
* Spitzer 9" fabricated rear with full chrome package, M.W. center section, axels & brakes
* Strange struts & brakes up front
* Carbon fiber seat enclosure, wheel tubs & dash insert
* Fuel system - Magna fuel 500 pump with Spitzer tank
* New Hoosier tires, front & rear with Aluma Star wheels
* Outlaw shifter with Biondo air shift
* Optima Red Top battery with 2nd battery provision
* Auto metered gauges
* MSD 7AL-2 ignition box with pro power coil & three step box
* Entirely professionally wired
etc., etc., etc.
ENGINE
* 505 CU. IN. BBC
* Cola crankshaft
* Eagle ESP rods with additional work & L-19 fasteners
* Ross pistons
* Comp Cams 7/4 swap cam
* Comps Best roller lifters
* Milidon ultra pan
* ATI balancer
* GM 4 bolt MK-4 block (289 casting)
* Arp studs on mains & heads
* Dart Pro-1 345 heads, programmed & flowed with sheet, now 354 C.C. intake runners, with Dart stainless valves, 2.300 & 1.880, Manley NexTech springs & titanium retainers, Jesel 1.7 shaft rockers with Trend Products pushrods
* Super Victor intake also programmed & flowed
* Pro Systems dominator flows 1098 CFM
* MSD distributor, crank trigger & plug wires, etc.
* Arp 12 point polished fasteners used throughout the assembly of this engine
TRANSMISSION & CONVERTER
* Janis/Rossler ProGlide with Dedenbear case & 1.80 straight cut planetary - all new
* ATI torque converter 8" with steel sprag built for this combo by "Nelson"
* ATI HD flywheel
* Showgun converter cooler (fan)
All parts on engine & trans combo are new with the exclusion of the engine block, which was pressure tested & professionally prepared.
PLEASE keep in mind this is a well thought out combination with zero runs. I am not looking to liquidate this car so be realistic.
Prelimarily, I would prefer emails on RJ's message system as opposed to phone calls. SERIOUS INQUIRIES ONLY.
Will separate this combination although the engine MUST sell first.
Complete car, 42,000
Roller, 28,500
Engine, 11,500
Trans & conv, 4,200
This item is NEW
Trades NOT ACCEPTED
Payment options:
| cash |
Item Location: AKRON, OH Get Directions To This City
Ad posted by: rattman (#67272)
RaceSpace Profile: View
Member Since: 2005-01-12
Number of Honor Payments: 3
Average Accepted Sale Price: $450.00
Average Honor Payment: $4.67
Phone Number: 330-773-6369

- Member has no other classified ads.
Your Recently Viewed Ads
- Ad #1341923: 1997 Monaco Signature 40'
- Ad #1575331: 34' LQ Motorcycle / ATV & Auto 6K Axles T
- Ad #1683858: 2005 Miller
- Ad #1338920: 2009 TOTERHOME (NICEST ON THE MARKET) OPTIMA
- Ad #1637402: Pavement 410 Sprint Car
- Ad #1691611: 07 polaris xp for sale
- Ad #1693351: NEW OLD STOCK FORD PARTS 1940's thru1970's
- Ad #1694755: 71-72 chevelle trunk floor 7 pcs brand new
- Ad #1585736: One Sweet Ride!! SALE OR TRADE!!
- Ad #1691163: MinnKota trolling motor

Questions & Answers about this ad
Question:
Hello, Nice roadster, any room for a 6'2" 225 lb driver. Thanks
Answer:
Hi, absolutely. In fact, a 6'4" 250 lb driver would be no problem. We actually purchased a special Kerkey seat to install in the original carbon fiber seat enclosure because my driver is 5'9" 185 lbs. As of yet, we have not fabricated the brackets for that seat. THANKS,Paul On [2009-11-08 09:59:26] 63split wrote: > Hello, > Nice roadster, any room for a 6'2" 225 lb driver. > Thanks
RESOURCE LINKS
- Financing
- Transportation/Shipping
- Purchase Protection
- RV Insurance
| Thank you for all your help, after posting my ad in RacingJunk.Com immediately I started to get emails from all over the West Coast, and it was sold in less than a week. This is a really great place to post your ads. I highly recommend it. Thanks |
| Bill - NV |









